Danh mục sản phẩm
Hỗ trợ trực tuyến
Hỗ trợ mua hàng

Mobile: 02436.231.170

Ms Huyền - Kinh doanh

Mobile: 0984.058.846

Tư vấn kỹ thuật Raspberry Pi

Mobile: 0862.628.846

Tư vấn kỹ thuật Module khác

Mobile: 0862.998.846

Mạch nạp ST-LINK

Mạch nạp ST-LINK
Mạch nạp ST-LINK
Nhà sản xuất: Waveshare
Mã hàng: C8-MN007
Trạng thái: Đặt hàng trước
Giá: 550,000 vnđ
Số lượng:  
   - Hoặc -   

In-circuit debugger and programmer for STM8 and STM32 MCUs; with IAR EWARM and Keil RVMDK and ST toolset

Description

The ST-LINK is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The SWIM and JTAG/SWD interface is used to communicate with the STM8 or STM32 microcontroller located on your own application board.

On the PC side, the USB full speed interface is used to communicate with:

  • ST Visual Develop (STVD) or ST Visual Program (STVP) software from
    STMicroelectronic's for the STM8,
  • ATOLLIC, IAR and KEIL Integrated Development Environments for the STM32.

Key Features

  • 5 V power supplied by USB connector
  • USB 2.0 full speed interface compatible
  • USB standard A to micro cable provided
  • SWIM specific features:
    • 1.65 V to 5.5 V application voltage supported on SWIM interface
    • SWIM low speed and high speed modes supported
    • SWIM programming speed rate:
      • 9.7 Kbytes/s in low speed
      • 12.8 Kbytes/s in high speed
    • SWIM cable for connection to an application with pin headers or 2.54 mm pitch connector
  • JTAG/SWD specific features:
    • 3 V to 3.6 V application voltage supported on JTAG/SWD interface and 5 V tolerant inputs
    • JTAG/SWD cable provided for connection to a standard JTAG 20-pin pitch 2.54 mm connector
  • Direct firmware update feature supported
  • Status LED which blinks during communication with PC
  • Operating temperature 0 to 50 °C

Application Example

Connecting the PC and STM8/STM32 application board through a ST-LINK to establish hardware connection :

Supported Devices

Microcontrollers supported by STVP release 3.2.8:

Product line

Microcontroller

STM32

STM32F100xx, STM32F101xx, STM32F102xx, STM32F103xx, STM32F105xx, STM32F107xx, STM32F2xxx, STM32F4xxx,

STM32L15xx6, STM32L15xx8,STM32L15xxB, STM32L151xC, STM32L151xD, STM32L152xC, STM32L152xD, STM32L162xD,

STM32TS60,

STM32W108C8, STM32W108xB, STM32W108xC, STM32W108xZ

STM8

STM8AF51x, STM8AF52x, STM8AF61x, STM8AF62x,STM8AH51x, STM8AH61x, 

STM8S003K3, STM8S003F3, STM8S005C6, STM8S005K6, STM8S007C8, STM8S103xx, STM8S105xx, STM8S207xx, STM8S208xx, STM8S903F3, STM8S903K3, 

STM8L101xx, STM8L15x, STM8L16x,

STM8TL52x4,STM8TL53x4

 

Connection with STM8 applications

The ST-LINK should be connected to the STM8 application via the SWIM separate-wires cable, which is delivered with the product.

As the SWIM separate-wires cable has independent connectors for all pins on one side, it is possible to connect the ST-LINK to an application board without a standard SWIM connector. On this flat ribbon all signals are referenced by a specific color and a label to ease the connection on target.

SWIM header pinout
Figure 1. Standard SWIM header pinout
SWIM cable
Figure 2. SWIM separate-wires cable connected on ST-LINK target connector even pins
connection with STM8 application
Figure 3. Connected to a STM8 application board via SWIM separate-wires cable
 

Connection with STM32 applications

For STM32 developments the ST-LINK must be connected to the application using the standard 20-pin female-female JTAG flat ribbon provided.

Debugging connector layout
Figure 4. Debugging connector layout on ST-LINK and flat cable
 
connection with STM32 application
Figure 5. Connected to a STM32 application board via 20-pin female-female JTAG flat ribbon
 

Downloads

Development resources:user manual, driver, software, etc.

Wiki: www.waveshare.com/wiki/ST-LINK

 

 

 

Viết đánh giá

Họ và tên:


Đánh giá của bạn: Lưu ý: Không hỗ trợ HTML!

Bình chọn: Xấu           Tốt

Nhập mã bảo vệ: