+ 40PIN GPIO tiêu chuẩn, hỗ trợ bo mạch Raspberry Pi series, Jetson Nano
+ Hỗ trợ gọi điện thoại, SMS, TCP, UDP, DTMF, HTTP, FTP, v.v.
+ Hỗ trợ định vị trạm gốc LBS
+ Giao diện USB tích hợp, để kiểm tra Lệnh AT, thiết lập kết nối mạng, v.v.
+ Bộ chuyển đổi USB sang UART CP2102 tích hợp, để gỡ lỗi nối tiếp
+ Chân điều khiển UART đột phá, để kết nối với các bảng chủ như Arduino / STM32
+ Khe cắm thẻ SIM, hỗ trợ thẻ SIM 1.8V / 3V
+ Khe cắm thẻ TF để lưu trữ dữ liệu như tệp, tin nhắn, v.v.
+ Giắc cắm âm thanh tích hợp và bộ giải mã âm thanh để thực hiện cuộc gọi điện thoại
+ Đèn báo LED 2x, dễ dàng theo dõi trạng thái làm việc
+ Bộ dịch điện áp tích hợp, điện áp hoạt động có thể được định cấu hình thành 3.3V hoặc 5V thông qua jumper
+ Tốc độ truyền: 300bps ~ 4Mbps (mặc định: 115200bps)
+ Tốc độ truyền baud tự động: 9600bps ~ 115200bps
+ Điều khiển thông qua các lệnh AT (bộ lệnh 3GPP TS 27.007, 27.005 và V.25TER)
+ Hỗ trợ bộ công cụ ứng dụng SIM: SAT Class 3, GSM 11.14 Release 99, USAT
+ Đi kèm với tài nguyên phát triển và sách hướng dẫn (ví dụ cho Raspberry Pi / Jetson Nano / Arduino / STM32)
FREQUENCY BAND | |
---|---|
LTE Cat-4 | LTE-FDD: B1/B3/B5/B8 |
LTE-TDD: B38/B39/B40/B41 | |
3G | UMTS/HSDPA/HSPA+: B1/B8 |
2G | GSM/GPRS/EDGE: 900/1800 MHz |
SMS AND AUDIO | |
SMS | Supported types: MT, MO, CB, Text, PDU |
Storage: USIM card and ME (default) | |
Audio feature | Supports echo cancellation |
Supports noise reduction | |
OTHERS | |
Power supply | 5V |
Operating voltage | 5V / 3.3V (configured via jumper) |
Operating temperature | -30°C ~ 80°C |
Storage temperature | -45°C ~ 90°C |
Dimensions | 56.01mm × 65.00mm |
1. SIM7600CE-CNSE
2. CP2102 USB to UART converter
3. NAU8810 audio decoder
4. TXS0108EPWR voltage translator
+ translates 3.3V/5V into 1.8V
5. MP2128DT power chip
6. MP1482 power chip
7. Raspberry Pi GPIO header
+ for connecting with Raspberry Pi
8. SIM7600 control interface
+ for connecting with host boards like Arduino/STM32
9. SIM card slot
+ supports 1.8V/3V SIM card
10. TF card slot
+ for storing data like files, messages, etc.
11. 3.5mm earphone/mic jack
+ for audio actions like making telephoto call
12. USB interface
+ for testing AT Commands, and so on
13. USB TO UART interface
+ for serial debugging, or login to Raspberry Pi
14. MAIN antenna connector
15. Module power switch
16. Network status indicator
17. Power indicator
18. UART selection jumper
A: access Raspberry Pi via USB to UART
B: control the SIM7600 by Raspberry Pi
C: control the SIM7600 via USB to UART
19. PWR selection jumper
+ PWR - 3V3: auto startup on power-up
+ PWR - D6: startup/shutdown by the Raspberry Pi D6 pin
20. Flight mode selection jumper
+ NC by default, no flight mode control pin
+ Flight - D4: flight mode is controlled by the Raspberry Pi D4 pin
21. Operating voltage selection jumper
+ VCCIO - 3.3V: set operating voltage as 3.3V
+ VCCIO - 5V: set operating voltage as 5V
22. USB connector solder pads
23. BOOT forced programming solder pads