Giỏ hàng của bạn đang trống!
Danh mục sản phẩm
- KHUYẾN MÃI (22)
- Raspberry Pi 5 (19)
- SẢN PHẨM MỚI NHẤT (35)
- ASUS Tinker (49)
- Chơi âm thanh (9)
- Màn hình (51)
- Raspberry Pi 4 Model B (94)
- AI Computer and System on Module (52)
-
NVIDIA Jetson Nano Developer Kit (118)
- Module 4G/3G/2G/GNSS dành cho NVIDIA Jetson Nano (7)
- Màn hình LCD cho Jetson Nano (16)
- Robot dành cho Jetson Nano (2)
- Jetson AI Boards (26)
- Camera cho Jetson Nano (30)
- Nguồn cho Jetson Nano (12)
- Vỏ hộp và quạt tản nhiệt cho Jetson Nano (8)
- Module cho Jetson Nano (10)
- Phụ kiện khác cho Jetson Nano (16)
- LattePanda (37)
- BeagleBone (5)
- Raspberry Pi B+/Raspberry Pi2/Raspberry Pi3 (256)
- Raspberry Pi Zero (24)
- Module Boards (208)
- Modules cảm biến (113)
- Mạch Arduino (68)
- Mô hình Robot (18)
- Robot dành cho Raspberry Pi (7)
KHUYẾN MÃI
CC Debugger
Giá: 680,000 vnđ
Debugger and Programmer for CCxxxx RF System-on-Chip (SoC) devices, CCxxxx RF transceivers, and CC85xx devices with PurePath Wireless Configurator
Description
The CC Debugger is primarily used for debugging and programming the flash on CCxxxx 8051-based System-on-Chip (SoC) devices from Texas Instruments. CC Debugger also supports CCxxxx RF transceivers. In addition, CC Debugger is used for configuring the CC85xx devices with PurePath Wireless Configurator.
Key Features
-
Performance
- Compatible with the original TI CC Debugger
- Supported Operating Systems: Windows 2000, Windows xp sp2/sp3, Windows Vista 32bit, Windows 7 32bit
- Target voltage: 1.2V～3.6V
- Capable of powering the target board from the debugger
- Operating temperature: 0℃～85℃
-
Supported Software
- IAR Embedded Workbench For C8051
- SmartRF Flash Programmer
- SmartRF Studio
- SmartRF Packet Sniffer
- PurePath Wireless Configurator
-
Connects to PC
- Computer connection via USB interface
-
Connects to target board
-
Target board connection via 10-pin IDC connector (2x5 2.54mm pitch). The figure below shows the header pinout:
-
Target board connection via 10-pin IDC connector (2x5 2.54mm pitch). The figure below shows the header pinout:
Supported Devices
-
Programming and debugging the following 8051-based system-on-chips from Texas Instruments:
- CC1110, CC1111
- CC2430, CC2431
- CC2510, CC2511
- CC2530, CC2531, CC2533
- CC2540, CC2541
- CC2543, CC2544, CC2545
-
Controlling the following transceivers from SmartRF Studio:
- CC1120, CC1121, CC1125, CC1175
- CC1101, CC110L, CC113L, CC115L
- CC2520
-
Configuring the CC85xx devices with PurePath Wireless Configurator:
- CC8520, CC8521
- CC8530, CC8531
LED Status
- OFF: The debugger has no power or there is no valid firmware on the debugger.
- AMBER (BOTH LEDS ON): The debugger is powered, but there is no valid firmware.
- RED LED BLINKING: The Debugger is in Boot Recovery Mode.
- RED LED ON: No device detected. This might be due to old firmware on the CC Debugger, or a problem with the hardware connection (make sure the target board is properly powered and connected correctly).
- GREEN LED ON: The target device has been properly detected. It is possible to start programming/debugging.
Downloads
Development resources:user manual, schematic, firmware, software, etc.
Viết đánh giá
Họ và tên:Đánh giá của bạn: Lưu ý: Không hỗ trợ HTML!
Bình chọn: Xấu Tốt
Nhập mã bảo vệ:
